悬浮窗
悬浮窗
QQ咨询
电话联系
13075398219
扫一扫
二维码
您好,欢迎访问买球赛竞猜的app哪个好,主要业务:济南亚克力发光字,形象墙发光字,吸塑发光字,冲孔发光字等广告制作
咨询热线:13075398219
您现在所在的位置: 首页> 新闻资讯 >

发光字怎么装灯!

所属分类:新闻资讯 发布时间:2021-02-22 来源:买球赛竞猜的app哪个好 浏览量:

一面亚克力发光字底和侧面都是连上一起的,采用铁皮焊接,需要把正面给扣上去,三面发光字底是pvc材质的,采用的粘贴的方式,把底和侧面粘贴在一起,不锈钢发光字后面则是采用比较厚的pvc材质一般为1公分左右。不同的发光字采用的底材质都是不同的,制作的方法也都是不同的。
One side of the acrylic light-emitting word bottom and side are connected together, using iron sheet welding, need to buckle up the front, three sides of the light-emitting word bottom is PVC material, using the paste method, paste the bottom and side together, stainless steel light-emitting word back is using thicker PVC material, generally about 1 cm. Different luminous characters are made of different materials and different methods.
采用铁皮焊接成型,把光源排到字体壳里面,间距一般为2-3cm。底和侧面是采用锡焊的方式,焊接好了给予打磨光滑即可。
The light source is arranged in the font shell with a distance of 2-3cm. The bottom and side are soldered with tin, and then polished.
三面亚克力发光字,主要的工艺就是粘贴,折弯,底壳采用pvc板材比较的多,把pvc板材给予雕刻成字的大小,光源排列在pvc板材上面,切割成型,粘贴即可
Three side acrylic luminous characters, the main process is paste, bending, the bottom shell using PVC plate is more, the PVC plate to carve into the size of the word, the light source arranged on the PVC plate, cutting molding, paste
               济南形象墙发光字
树脂发光字的底和排灯的方式的,做好的字体正面朝上放在铝铂纸上用水彩笔画出字型,先贴棉胶,将合适的固定件摆放置,3 米以下小字一般用细的不透钢条穿过笔画伸出 1 个厘米左右,3 米以上的大字一般用扁铁穿过笔画伸出 5—10 厘米。 将做好的 LED 模组用双面胶固定在铝铂纸,LED 正常离字边 3—4 厘米不要靠边太近,LED 模组问距正常 4—5 厘米,根据字的厚度,字边高间距大一点,字边低间距小一点,排放电路时要每 20 组与两根主线并联这一点非常关键,主线的粗细要在 1—1.5 以上、用橡胶条围好字型,防止橡胶条与铝箔粘与不牢不可破建议用热熔胶打一遍,倒入配好的原料树脂发光字+0.2%的白色浆+0.3-1.5%固化剂夏天-冬天0.3—0.6 厘米厚度,将字体扣上,固化后立刻用直尺沿边将多余的树脂发光字划掉。几个小时以后沿字边将铝箔纸。
The bottom of the resin luminous characters and the way of arranging the lamps are arranged. The prepared fonts are placed face up on the aluminum platinum paper, and the watercolor strokes are used to draw the characters. First, the cotton glue is pasted, and the suitable fixings are placed. The small characters below 3 meters are generally passed through the strokes with thin impervious steel bars, and the strokes extend about 1 cm. The large characters above 3 meters are generally passed through the strokes with flat iron, and the strokes extend 5-10 cm. Fix the LED module on the aluminum platinum paper with double-sided adhesive tape. The normal distance between the LED module and the word edge is 3-4cm, not too close to the edge. The normal distance between the LED module and the word edge is 4cm-5cm. According to the thickness of the word, the high space between the word edge is larger, and the low space between the word edge is smaller. When discharging the circuit, it is very important to connect every 20 groups with two main lines in parallel. The thickness of the main line should be 1-1.5cm In order to prevent the rubber strip from sticking to the aluminum foil, it is recommended to use hot melt adhesive to type the characters. Pour in the prepared raw material  resin luminous characters + 0.2% white paste + 0.3-1.5% curing agent. The thickness of the characters is 0.3-0.6cm from summer to winter. After curing, scratch off the redundant resin luminous characters with a ruler. After a few hours, put the foil along the edge of the word.
热门产品 / HOT PRODUCT
首页 产品 电话 置顶