悬浮窗
悬浮窗
QQ咨询
电话联系
13075398219
扫一扫
二维码
您好,欢迎访问买球赛竞猜的app哪个好,主要业务:济南亚克力发光字,形象墙发光字,吸塑发光字,冲孔发光字等广告制作
咨询热线:13075398219
您现在所在的位置: 首页> 发光字制作知识 >

吸塑发光字的安装方法详解!

所属分类:发光字制作知识 发布时间:2020-12-02 来源:买球赛竞猜的app哪个好 浏览量:

吸塑发光字的安装方法详解
Detailed explanation of installation method of blister luminous words
一、先将单独的字或偏旁部首的吸塑产品侧面的螺钉扭开,将字分成底板和面板2个部分。
1、 First of all, the screw on the side of the blister product with single character or side part is twisted, and the word is divided into two parts: the bottom plate and the panel.
二、将面板底边绕开LED部位打孔用螺钉固定不动再安装壁面上,按设计之板安装好,并将每一个字的线结稳固好。
2、 Hole the bottom edge of the panel around the LED part, fix it with screws, and then install it on the wall. Install it according to the designed board, and firmly fix the wire knot of each word.
三、在整排字的上边或下边排一红一绿的两根主线(2.5的铜芯电线),随后将每一个单独的吸塑发光字或吸塑字的笔画的线头,按红接红,绿接绿做好并联联接,随后将系统总线的红绿线相匹配连接变压转换器。
3、 Two main lines (2.5 copper core wires) with red and green lines are arranged on the top or bottom of the whole typesetting. Then, connect the red and green wires of each single blister luminous character or blister character in parallel. Then, match the red and green wires of the system bus to connect the transformer.
              济南吸塑发光字
四、再将变压转换器的(AC)区域的L、N连接220V电源(2.5的铜芯电线),如安装部位较低,尽量是连上接地线。
4、 Then connect L and N in the (AC) area of the transformer to the 220 V power supply (2.5 copper core wire). If the installation position is low, try to connect the grounding wire.
五、线全都连上,接电源后如LED灯不亮,则将LED的主线的红绿部位互换就可以了。
5、 All the lines are connected. If the LED light is not on after the power supply is connected, the red and green parts of the main line of the LED can be interchanged.
六、然后将面板合上扭紧螺钉。
6、 Then close the panel and tighten the screws.
常见注意事项:
Common precautions:
1、切忌将每一个字的线结都直接连接到220V电源上,要不然LED灯全都损毁。
1. Do not connect each word of the wire knot directly to the 220 V power supply, or all LED lights will be damaged.
2、安装前可首先用一个字按正确性的方法实验一下子,再全都安装。
2. Before installation, you can first use one word to test the correctness of the method, and then install them all.
3、请使用防水胶带包好连接头,变压转换器应放置防水防雨区域及自然通风散热优良。
3. Please wrap the connector with waterproof tape. The transformer should be placed in a waterproof and rainproof area with good natural ventilation and heat dissipation.
热门产品 / HOT PRODUCT
首页 产品 电话 置顶